Home > Error Code > Balboa Hot Tub Error Codes

Balboa Hot Tub Error Codes

Contents

I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah If the water level is okay, make sure the pumps have been primed.On the fifth occurrence of the above message the panel will display -LFThis indicates a persistent flow problemThe heater In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced. Heat Related Pump Not Primed.9. Check This Out

Select "Message Other than CrC or CHKSUM FAIL" Below. Remove the spa hot tub hard cover and allow water to cool off. Check for excessive filter duration. Check for clogged filter.

Balboa Hot Tub Error Codes

Your cache administrator is webmaster. This indicates a Possible Problem with the System Board. Harold Asmis 3.794 görüntüleme 7:06 Hot Tub Heater Troubleshooting - Süre: 2:26.

This could be a flow problem.Check the water levels in tub. Low Water Level.2. It's either a Smart S-3 or Genius Series. Balboa Hot Tub Turn Off Economy Mode Clean and Condition Spa Cover per Manufacturers Instructions.

Kategori Kişiler ve Bloglar Lisans Standart YouTube Lisansı Daha fazla göster Daha az göster Yükleniyor... Balboa Spa Control Manual All Pumps and Blower are ON for at least 4 Minutes After Temp is 45°F (7.2°C) or Above at the Sensors, or when the Aux Freeze Switch Opens. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. see it here The most common valve; the tee handle valve (also known as gate or slice valve), will show that the handle is up, but in many cases the gate is still half

th3/39 On startup indicates water temperature less than 39° F. Leisure Bay Spa Error Codes FLO Flow Switch (heater is deactivated. Fuse(s) to system is/are blown.The hot tub control panel is automatically disabled until return of power, but the system will function to reset the time of day of each time of Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated).

Balboa Spa Control Manual

HLoH Hi Limit Over Heat. navigate to these guys HL High limit switch tripped. Balboa Hot Tub Error Codes You can change this preference below. Sl Code On Hot Tub The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2.

I cannot confirm the codes you are seeing.JACUSTOMER-6qmvr0uk- : No, I can try to get the filter out and see if it helps. his comment is here There also could be a voltage problem, excessive voltage creates heat. It may be possible for the stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. If the hot tub does not reset, turn off the power to the spa and call your dealer or service company.         IC"Ice" - This is a Potential freeze condition detectedNo Vita Spa Error Codes

After the Problem has been Resolved, you Must Press Any Button to Reset and Restart Heater Start Up. Flo Improper flow or pressure switch malfunction Cool Water temp 20° below set point ICE Potential freeze condition has been detected Sn1 Hi-limit sensor malfunction Sn3 Temp sensor malfunction SnA Spa There is Not Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. http://robertwindows.com/error-code/hp-desktop-error-codes.html Heat Related Pump Not Running.8.

Remove the Spa Cover and allow Sanitizer to Dissipate, or do a Partial Water Change.Note: If you do Not have an ORP Sensor installed in the Spa System, you should Never Marquis Spa Error Codes I will go find it for you.Poolservice123 : It would be the error code.JACUSTOMER-6qmvr0uk- : It could be FL and the bottom of the L is missing. If the GFCI does not trip for some reason, the gFI fault will appear and the HOt flag will be set.If the spa is subsequently powered down and then powered up

If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes

This is a normal spa function; no further action is necessary.When either sensor reads below 4.5° C, the system provides freeze protection. This mode is best suited for extended leaves from home and also when it is not important to maintain constant water temperature, such as vacations or business trips.Click here for the Leisure_Bay_Spas_owners_ManualShare this:TweetShare I've been 11/26/2016 11/26/2016 dontrudeau I have a call spa atlantic classic series model 05-5m-ca31. 11/25/2016 11/25/2016 rickspaserv I bout a used hot springs souvergn. Balboa Hot Tub Codes F8 Wait 4 Minutes or Press any Temp Related Button to Exit Priming Mode to Normal Operation.Note: On some Early VS and GS Systems (prior to Version 23) equipped with a "Mode"

We will not be held liable for any injuries that may result from the troubleshooting or installation of any electrical components in your hot tub spa unit.Error codes indicate a problem PnL Communication between the panel and circuit board is faulty. ---- Watchdog" (spa is deactivated) A problem has been detected. Email Address: Password: You will be prompted to enter your password on the next page Create an account Forgot Password? navigate here This is an Operational Message, Not an Error Indication.

Spa has shut down. Thought that would fix it. If there is Now a "CrC" or "CHKSUM FAIL" Error Message, contact your Dealer or Service Organization. Back to Top SnS or Sn Message SnS or Sn MessageIf the SnS or Sn Message is Alternating with the Water Temperature on the Display, it is a Possible Sensors Out

No action is necessary. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different. Any and all service should be performed by a licensed spa technician. On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States

any ideas?? Just let me know and io poolguy810 : and I'll be happy to help out any way I can, thanks, Jeff JACUSTOMER-f7hnkhdo- : Checked the cable from the touchpad to the