Home > Error Code > How To Fix Dr Code On Hot Tub

How To Fix Dr Code On Hot Tub

Contents

The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. Both are secured with black plastic nut around the gray cable. softcellelectrical 49.399 görüntüleme 4:15 How To Diagnose and Repair Hot Spring Spa - Süre: 4:52. covers error codes hot tub leisure bay spas owners manual Share This Previous Post← Beachcomber Hot Tubs Error Codes & Information Beachcomber Hot Tubs Error Codes & Information Next PostHow to Check This Out

Back to Top SbY or STANDBY MODE Message The Spa is Operating in the "Standby" (SbY) Mode.All Automatic Spa System Functions are Disabled so that Pumps and Blower will not turn Also, the Pumps won't go on. Bu tercihi aşağıdan değiştirebilirsiniz. Back to Top PHH or PH IS HIGH LOWER PH Message At the pH Sensor, the "pH Level is High" (PHH).With a pH Sensor Installed in the System, the pH Level directory

How To Fix Dr Code On Hot Tub

Power on the spa must be cycled before the heater will function again. Press "Mode" Button to Clear Message. Shut the spa power off, remove the filter and make sure all the jets are open. Contact your Dealer or Service Organization.

I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. ThanksPoolservice123 : I'll see who I can find.JACUSTOMER-6qmvr0uk- : Never Mind. Also, on the VS/GS Models, Freeze Protect Mode overrides Priming Mode, and All pumps will be on in Freeze Protect Mode.The purpose of Priming Mode is to allow the user to Hot Tub Error Code Dry YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART.

Check the water temperature with an accurate temperature thermometer. The Sensors are Verified Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors. Safety should ALWAYS be your first consideration! The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open

Could it be that there is some dirt in the pipes causing this problem? What Does Dr Mean On A Hot Tub If water is flowing from the circ pump outlet, proceed to test all the other pumps.If the Circ Pump is primed, or if you Do Not have a Circ Pump, then:- AC IN OK NO LIGHTS ON BOARD AND 11/21/2016 11/21/2016 alumalite X Ask a Pool and Spa Expert Get a Professional Answer. 100% Satisfaction Guaranteed. 50 Pool and Spa Experts are Back to Top ICE, IC, or FREEZE COND Message A Potential Freeze Condition has been Detected, and "Ice" (ICE) in the System is being Prevented.44°F (6.7°C) or Lower has been Detected

Leisure Bay Spa Error Codes

If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. http://www.spadepot.com/spa-error-codes.htm Back to Top OHH, HH, or HTR TEMP LMT SERVICE REQD Message There is an "Over Heated Heater" (OHH or HH) Condition.One of the Water Temp Sensors has detected 118°F (47.8°C) How To Fix Dr Code On Hot Tub everythign was working. 11/23/2016 11/23/2016 JACUSTOMER-27j3luit- I have an intex inflatqble spa saltwaater system..The temps 11/23/2016 11/23/2016 Poolservice123 I have a 2015 Optima -- i am getting a flo2 error message Balboa Hot Tub Error Codes Dirty Filter.5.

Back to Top Pr or PRIMING MODE TAKES 4 MIN Message The Spa is Operating in "Priming" (Pr) Mode.The Spa has just been powered up and is in Priming Mode for his comment is here This is an Operational Message, Not an Error Indication. Once this is done check ACROSS the heater element post, you should have either 110 volts or 220 volts depending on what voltage is operating the control box. Turn the power back on, you have five seconds to join the wires together, do not join them before you turn the power on. How To Fix Flo Error Hot Tub

If there is No Error Message, Select "No Error Message" Below. NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets. In extremely hot weather, check for proper cabinet ventilation. this contact form Top up if necessary.

I have been servicing spas for over 20 years and can answer technical questions for most major spa control systems such as Balboa, Hydro Quip and Gecko. Vita Spa Error Codes In the Elite series Leisure Bay Spas boasts 4 different models the Niagara, Hatteras, Cordova, and Harbor Cove. Test and Reset the G.F.C.I.

It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing.

Fix my Pool and Spa is online now I have Elite Series from Leisure Bay Spas, We have emptied Customer Question I have Elite Series from Leisure Bay Spas, We have Back to Top OHS, OH, or SPA TEMP LMT Message There is an "Over Heated Spa" (OHS or OH) Water Condition.One of the Water Temp Sensors has detected 110°F (43.3°C) Incoming Do not do this more than 5 times. Marquis Spa Error Codes Heat Related Pump Not Primed.

It seems that every time I fix one thing another just happens to go wrong. Back to Top drn or DRAINING Message While in Standby Mode, "Drain" (drn) Mode has been Activated.The "Jets 1" Button has been Pressed while in the Standby Mode, and Pump 1 All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 180 Days, but some Spa Brands or Models may be Different. navigate here If the error persists, contact your dealer or service company.          LFContinuous low flow. (Displays on the fifth occurrence of "HL" error within a 24 hour cycle.) Heater is shut down,

Remove, Clean, and Reinstall Spa Filter Cartridge per Manufacturers Instructions. Then you have to check if the flow of water is sufficient in the heater and to remove the air by unscrewing it. Dirty Filter.5.