Home > Lexmark Printer > Lexmark Printer Error Code Ec5

Lexmark Printer Error Code Ec5

Contents

Replace print head or ribbon cable. Error 44 Defective font card installed in font slot. Paper not being picked up check paper tray & pickup rollers. For non-touch-screen printer models, press to confirm.Cancel the print job.Change [paper source] to [custom type name] load [orientation]Try one or more of the followingLoad the correct paper size and type in Check This Out

Make sure fuse is installed correctly, Verfy proper fuser is being used. For non-touch-screen printer models, press to confirm.Cancel the print job.Change [paper source] to [paper size] load [orientation]Try one or more of the following:Load the correct paper size and type in the Thank you for the speedy shipment and response. For non-touch-screen printer models, press to confirm.Select Scan from flatbed to continue scanning from the scanner immediately after the last successful scan job. http://www.all-laser.com/aerrorlex/

Lexmark Printer Error Code Ec5

Cycle power Defective font card Defective system board 44 Font Card Error See 43 45 Downloaded Font Error Software setup Software drivers System board 46 Download Character Error See 45 47 Card format In Photo mode, memory card inserted has incorrect or unsupported format. For non-touch-screen printer models, press to confirm.Note:If the message appears again, then contact your system support person. CUSTOMER LOG IN SHOPPING CART Home Brother Canon Dell Epson

See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted. Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system The All-In-One can scan up to 19200 dpi, so it is possible to exceed the amount of data a file can hold. Lexmark Printer Error Symbols To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page.

A second memory card is inserted. Lexmark Engine Error Can be system board or printhead. If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr. Error 924 Open circuit detected in thermistor circuit.

Load correct size Error 28 Input sensor not made after pick attempt. 938.06 Service System Electronics Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. For non-touch-screen printer models, press to confirm.Turn off the printer, and then turn it back on.SMTP server not set up.

Lexmark Engine Error

All rights reserved. Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. Lexmark Printer Error Code Ec5 Check connections to the to interconnect card assembly. Lexmark Error Codes Problem While in Photo mode, a memory card with no images is inserted.

Press Stop/Clear on the control panel to cancel printing. his comment is here If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. For more information, see Installing the print cartridges. For non-touch-screen printer models, press to confirm.Select Finish job without further scanning to end the last successful scan job. Lexmark Printer Error Lights

Error 26 Duplex unit is installed but paper tray is not sensed. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. Replace the assys in the following order 1. this contact form Error 26 Duplex unit is installed but paper tray is not sensed.

Press “GO” to clear message and temporarily continue Install OPC Belt/Photo Developer Error 84 Transfer Drum Exhausted The Transfer drum has reached the end of its life and must be replaced. Lexmark Ms310dn Error Codes Run the Quick Disk Test. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct.

Check the toner metering cam on back of suspect cartridge.

Check the TMC pin in the cartridge contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly. test). Size Warning In Photo mode, resized image is larger than the selected blank paper size. Lexmark Crc Failed Do Not Power Off For non-touch-screen printer models, press to confirm.Install additional printer memory.Network[x] software error[54]Try one or more of the following:From the printer control panel, select Continue to continue printing.

The fuser, melts or fuses the toner to the media and has a heat roller and a pressure roller. Imaging component usage beyond the intended life may damage your Lexmark printer or associated components.Warning--Potential Damage:Use of third-party supplies or partscan affect warranty coverage. Check the TMC pin in the cartridge contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly. http://robertwindows.com/lexmark-printer/lexmark-printer-drivers-for-windows-10.html For non-touch-screen printer models, press to confirm.Scanner jam, remove all originals from the scanner [2yy.xx]Remove the jammed paper from the scanner.Scanner jam, remove jammed originals from the scanner [2yy.xx]Remove the jammed

Power printer off one to two minutes. For more information, see Loading paper. Replace printhead, system board or ribbon cable. This can significantly improve scanning and overall system performance.

The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. We stock the full range of Lexmark service parts needed for preventive maintenance and repair service. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is For non-touch-screen printer models, press to confirm.Turn the printer off, and then turn it back on.

Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed. See “Network Wrap Tests” on page 23. Press Select. If the message appears again after completing the setup, then contact your system support person.Fax Station Number not set up.

It may be necessary to remove the re drive assembly to observe the lamp cycling on and off. Brand names for printer ink are just reference. Remove and reinstall print cartridge. Jump to error 92X Some Lexmark printers have indicator lights which indicate by solid, blinking or off, an error condition.

Perform fuser service check. Error 43 Font card format not supported by printer. Controller Board 2. For non-touch-screen printer models, press to confirm.Memory full, cannot print faxesFrom the printer control panel, select Continue to clear the message without printing.

y indicates the value of the cartridge region. Verify latch relay is operating - slowly close door and listen for interlock switch 3. For more information, see the instruction sheet that came with the supply or see the "Replacing supplies" section of the User's Guide.Note:If you do not have a replacement imaging unit, then